OpenBSD manual page server

Manual Page Search Parameters
PCTR(4) Device Drivers Manual (amd64) PCTR(4)

pctr — driver for CPU performance counters

pseudo-device pctr 1

The pctr device provides access to the performance counters on AMD and Intel brand processors, and to the TSC on others.

Intel processors have two 40-bit performance counters which can be programmed to count events such as cache misses, branch target buffer hits, TLB misses, dual-issues, interrupts, pipeline flushes, and more. While AMD processors have four 48-bit counters, their precision is decreased to 40 bits.

There is one ioctl call to read the status of all counters, and one ioctl call to program the function of each counter. All require the following includes:

#include <sys/types.h>
#include <machine/cpu.h>
#include <machine/pctr.h>

The current state of all counters can be read with the PCIOCRD ioctl, which takes an argument of type struct pctrst:

#define PCTR_NUM	4
struct pctrst {
	u_int pctr_fn[PCTR_NUM];
	pctrval pctr_tsc;
	pctrval pctr_hwc[PCTR_NUM];
};

In this structure, contains the functions of the counters, as previously set by the PCIOCS0, PCIOCS1, PCIOCS2 and PCIOCS3 ioctls (see below). contains the actual value of the hardware counters. is a free-running, 64-bit cycle counter.

The functions of the counters can be programmed with ioctls PCIOCS0, PCIOCS1, PCIOCS2 and PCIOCS3 which require a writeable file descriptor and take an argument of type unsigned int. The meaning of this integer is dependent on the particular CPU.

The time stamp counter is available on most of the AMD and Intel CPUs. It is set to zero at boot time, and then increments with each cycle. Because the counter is 64-bits wide, it does not overflow.

The value of the time stamp counter is returned by the PCIOCRD ioctl, so that one can get an exact timestamp on readings of the hardware event counters.

The performance counters can be read directly from user-mode without need to invoke the kernel. The macro (ctr) takes 0, 1, 2 or 3 as an argument to specify a counter, and returns that counter's 40-bit value (which will be of type ). This is generally preferable to making a system call as it introduces less distortion in measurements.

Counter functions supported by these CPUs contain several parts. The most significant byte (an 8-bit integer shifted left by PCTR_CM_SHIFT) contains a counter mask. If non-zero, this sets a threshold for the number of times an event must occur in one cycle for the counter to be incremented. The counter mask can therefore be used to count cycles in which an event occurs at least some number of times. The next byte contains several flags:

Enables counting of events that occur in user mode.
Enables counting of events that occur in kernel mode. You must set at least one of PCTR_K and PCTR_U to count anything.
Counts edges rather than cycles. For some functions this allows you to get an estimate of the number of events rather than the number of cycles occupied by those events.
Enable counters. This bit must be set in the function for counter 0 in order for either of the counters to be enabled. This bit should probably be set in counter 1 as well.
Inverts the sense of the counter mask. When this bit is set, the counter only increments on cycles in which there are no events than specified in the counter mask.

The next byte (shifted left by the PCTR_UM_SHIFT) contains flags specific to the event being counted, also known as the unit mask.

For events dealing with the L2 cache, the following flags are valid on Intel brand processors:

Count events involving modified cache coherency state lines.
Count events involving exclusive cache coherency state lines.
Count events involving shared cache coherency state lines.
Count events involving invalid cache coherency state lines.

To measure all L2 cache activity, all these bits should be set. They can be set with the macro PCTR_UM_MESI which contains the bitwise or of all of the above.

For event types dealing with bus transactions, there is another flag that can be set in the unit mask:

Count all appropriate bus events, not just those initiated by the processor.

Events marked require the PCTR_UM_[MESI] bits in the unit mask. Events marked can take the PCTR_UM_A bit.

Finally, the least significant byte of the counter function is the event type to count. A list of possible event functions could be obtained by running a pctr(1) command with -l option.

/dev/pctr
 

[]
An attempt was made to set the counter functions on a CPU that does not support counters.
[]
An invalid counter function was provided as an argument to the PCIOCSx ioctl.
[]
An attempt was made to set the counter functions, but the device was not open for writing.

pctr(1), ioctl(2)

A pctr device first appeared in OpenBSD 2.0. Support for amd64 architecture appeared in OpenBSD 4.3.

The pctr device was written by David Mazieres <[email protected]>. Support for amd64 architecture was written by Mike Belopuhov <[email protected]>.

Not all counter functions are completely accurate. Some of the functions may not make any sense at all. Also you should be aware of the possibility of an interrupt between invocations of rdpmc() that can potentially decrease the accuracy of measurements.

October 5, 2019 OpenBSD-current